Welcome to the new Quilt in a Day community pages. Please use your old username and password to log in. If you forgot your password, you can reset it from the log in page. If you have questions about how the new board works, try the FAQ link above.
Octagonal Topper Tutorial
-
- Posts: 7227
- Joined: Sat Jan 13, 2007 5:05 am
Octagonal Topper Tutorial
Here is a tute for the toppper as requested. If you need a pattern for the Octagon,there is a tute here for that too.
OCTAGONAL TOPPER TUTE
( Pardon the purple marks on my ruler.Little hands did it!!(: )
STEP 1
You will need an Octagon and 2 sets of strips. My strips are 1 1/2 " wide for the first round,and 3 1/2" for the second round.
Step 2
sew 4 narrow stips to opposite sides of octagon (these are about 7 inches)
Step 3 trim off at an angle,lining up edge of ruler along edge of octagon..do second narrow sides the same way
Step 4 square off all sides to 1 inch,lining up edge of ruler with edge of octagon
Step 5 add second set in same manner,but trim by lining ruler on FIRST STRIP instead of octagon
Step 6
do opposite sides and trim before adding second sides...NOTE that the first strip will be narrower .This will match up after you sew on remaining sides.
Step 7
Now trim final corners,lining ruler on edge of octagon again,,,mine trim off at 4 inches
Step 8
You are ready to quilt....do not do anymore trimming until quilted,,,then line ruler up along egde of octagon again and trim all sides to 3 1/2 You are done and ready to bind.
These are my measurements,,,you may make wider or more strips as desired. Enjoy!!
OCTAGONAL TOPPER TUTE
( Pardon the purple marks on my ruler.Little hands did it!!(: )
STEP 1
You will need an Octagon and 2 sets of strips. My strips are 1 1/2 " wide for the first round,and 3 1/2" for the second round.
Step 2
sew 4 narrow stips to opposite sides of octagon (these are about 7 inches)
Step 3 trim off at an angle,lining up edge of ruler along edge of octagon..do second narrow sides the same way
Step 4 square off all sides to 1 inch,lining up edge of ruler with edge of octagon
Step 5 add second set in same manner,but trim by lining ruler on FIRST STRIP instead of octagon
Step 6
do opposite sides and trim before adding second sides...NOTE that the first strip will be narrower .This will match up after you sew on remaining sides.
Step 7
Now trim final corners,lining ruler on edge of octagon again,,,mine trim off at 4 inches
Step 8
You are ready to quilt....do not do anymore trimming until quilted,,,then line ruler up along egde of octagon again and trim all sides to 3 1/2 You are done and ready to bind.
These are my measurements,,,you may make wider or more strips as desired. Enjoy!!
-
- Posts: 1706
- Joined: Tue Jan 23, 2007 3:28 pm
Re: Octagonal Topper Tutorial
Thank you
-
- Posts: 1185
- Joined: Sat Dec 27, 2008 2:38 am
Re: Octagonal Topper Tutorial
Caroline, You do such a great job on these. I love looking at all of them. I printed this out to put in my pattern stash. Thanks
vivian1970
vivian1970
-
- Posts: 1600
- Joined: Sat Aug 11, 2007 8:22 am
Re: Octagonal Topper Tutorial
Thanks Caroline from Missouri for sharing how you are making all of the wonderful table toppers. I am going to have to try to make one. I have save the pattern now. It sure was kind of you to share.
-
- Posts: 7227
- Joined: Sat Jan 13, 2007 5:05 am
Re: Octagonal Topper Tutorial
You're welcome!
-
- Posts: 7335
- Joined: Mon May 12, 2008 5:38 am
Re: Octagonal Topper Tutorial
Caroline, thank you so much for this tutorial!! You are a sweetie!!
Joanne
Joanne
-
- Posts: 5119
- Joined: Wed Apr 02, 2008 8:50 am
Re: Octagonal Topper Tutorial
Caroline, I love your tutorials, they are always so clear and understandable. I can see it now the beginning of a new career! Quilting Tutorials By Caroline, sounds like a money maker to me
Vicky
Vicky
- Oasis
- Posts: 10354
- Joined: Fri May 04, 2007 6:23 pm
Re: Octagonal Topper Tutorial
Thanks Caroline......I'm going to get a binder so I can keep all your TUTES in one place.
Have Fun,
Linda S / OASIS
Linda S / OASIS
-
- Posts: 1352
- Joined: Sat May 05, 2007 5:32 am
Re: Octagonal Topper Tutorial
Thank You very much. I will be looking forward to making a few. I would like the pattern for the Octagon. Thanks for sharing.
Lowell
Lowell